|
| status_t | flash_impl_init (bool coredump_mode) |
| | Initialize the driver and bring the part to a state ready to accept commands.
|
| |
| status_t | flash_impl_set_burst_mode (bool enable) |
| | Enable or disable synchronous burst mode, if supported.
|
| |
| FlashAddress | flash_impl_get_sector_base_address (FlashAddress addr) |
| | Get the base address of the sector containing an address.
|
| |
| FlashAddress | flash_impl_get_subsector_base_address (FlashAddress addr) |
| | Get the base address of the subsector containing an address.
|
| |
| size_t | flash_impl_get_capacity (void) |
| | Get the flash capacity.
|
| |
| status_t | flash_impl_enter_low_power_mode (void) |
| | Enter a low-power state.
|
| |
| status_t | flash_impl_exit_low_power_mode (void) |
| | Leave the low-power state.
|
| |
| status_t | flash_impl_read_sync (void *buffer, FlashAddress addr, size_t len) |
| | Read data.
|
| |
| void | flash_impl_enable_write_protection (void) |
| | Enable write protection, if the part requires it to be enabled explicitly.
|
| |
| status_t | flash_impl_write_protect (FlashAddress start_sector, FlashAddress end_sector) |
| | Write-protect a range of sectors.
|
| |
| status_t | flash_impl_unprotect (void) |
| | Remove write protection.
|
| |
| int | flash_impl_write_page_begin (const void *buffer, FlashAddress addr, size_t len) |
| | Start writing up to a page.
|
| |
| status_t | flash_impl_get_write_status (void) |
| | Poll the status of a page write.
|
| |
| status_t | flash_impl_write_suspend (FlashAddress addr) |
| | Suspend an in-progress write so reads and erases are permitted.
|
| |
| status_t | flash_impl_write_resume (FlashAddress addr) |
| | Resume a suspended write.
|
| |
| status_t | flash_impl_erase_subsector_begin (FlashAddress subsector_addr) |
| | Start erasing the subsector containing an address.
|
| |
| status_t | flash_impl_erase_sector_begin (FlashAddress sector_addr) |
| | Start erasing the sector containing an address.
|
| |
| status_t | flash_impl_erase_bulk_begin (void) |
| | Start erasing the entire flash.
|
| |
| status_t | flash_impl_get_erase_status (void) |
| | Poll the status of an erase.
|
| |
| uint32_t | flash_impl_get_typical_subsector_erase_duration_ms (void) |
| | Get the typical subsector erase duration.
|
| |
| uint32_t | flash_impl_get_typical_sector_erase_duration_ms (void) |
| | Get the typical sector erase duration.
|
| |
| status_t | flash_impl_erase_suspend (FlashAddress addr) |
| | Suspend an in-progress erase so reads and writes are permitted.
|
| |
| status_t | flash_impl_erase_resume (FlashAddress addr) |
| | Resume a suspended erase.
|
| |
| status_t | flash_impl_blank_check_subsector (FlashAddress addr) |
| | Check whether the subsector containing an address is blank (all ones).
|
| |
| status_t | flash_impl_blank_check_sector (FlashAddress addr) |
| | Check whether the sector containing an address is blank (all ones).
|
| |
| void | flash_impl_use (void) |
| | Take a reference keeping the flash peripheral powered.
|
| |
| void | flash_impl_release (void) |
| | Drop one reference taken with flash_impl_use().
|
| |
| void | flash_impl_release_many (uint32_t num_locks) |
| | Drop several references taken with flash_impl_use().
|
| |
| status_t | flash_impl_read_security_register (uint32_t addr, uint8_t *val) |
| | Read a byte from a security register.
|
| |
| status_t | flash_impl_security_register_is_locked (uint32_t address, bool *locked) |
| | Check whether a security register is locked.
|
| |
| status_t | flash_impl_erase_security_register (uint32_t addr) |
| | Erase a security register.
|
| |
| status_t | flash_impl_write_security_register (uint32_t addr, uint8_t val) |
| | Write a byte to a security register.
|
| |
| const FlashSecurityRegisters * | flash_impl_security_registers_info (void) |
| | Get the security register layout.
|
| |
