---
title: "Pebble 2 Duo (asterix)"
canonical_url: https://developer.repebble.com/pebbleos/docs/boards/asterix/
last_updated: 2026-11-22
sdk_version: 4.44
---
# Pebble 2 Duo (asterix)

Source: https://developer.repebble.com/pebbleos/docs/boards/asterix/

## Overview

 ![Pebble 2 Duo](https://developer.repebble.com/pebbleos/docs/images/asterix.webp)Board:

`asterix`

SoC:

Nordic nRF52840

Platform:

Flint

Emulator:

`qemu_flint`

Pebble 2 Duo, announced as Core 2 Duo, is a rectangular black and white watch built around the Nordic nRF52840. Its firmware targets the Flint platform, which apps see as a 144 × 168 black and white display.

## Hardware

- **SoC** : [Nordic nRF52840](https://www.nordicsemi.com/Products/nRF52840), with an Arm Cortex-M4 with FPU, an integrated Bluetooth Low Energy radio, 1 MiB flash and 256 KiB RAM

- **Flash** : [GigaDevice GD25LQ255E](https://www.gigadevice.com/product/flash/spi-nor-flash/gd25lq255e), 32 MiB NOR

- **Display** : 144 × 168 black and white Sharp LS013B7DH01 memory LCD

- **Backlight** : PWM driven

- **Accelerometer and gyroscope** : [ST LSM6DSO](https://www.st.com/en/mems-and-sensors/lsm6dso.html)

- **Magnetometer** : [MEMSIC MMC5603NJ](https://www.memsic.com/magnetometer-2)

- **Pressure** : [Bosch BMP390](https://www.bosch-sensortec.com/products/environmental-sensors/pressure-sensors/bmp390/) barometric pressure sensor

- **Ambient light** : [TI OPT3001](https://www.ti.com/product/OPT3001)

- **Vibration** : [TI DRV2604](https://www.ti.com/product/DRV2604) haptic driver

- **Microphone** : PDM, on the nRF52840 PDM interface

- **Speaker** : [Renesas DA7212](https://www.renesas.com/en/products/da7212) audio codec

- **Power** : [Nordic nPM1300](https://www.nordicsemi.com/Products/nPM1300) PMIC and battery charger

## Connecting a programmer

Pebble 2 Duo is programmed with the [Core B2B v2](https://developer.repebble.com/pebbleos/docs/programmers/core_b2b_v2.md), the programmer of its firmware development kit. The mainboard has a B2B (board-to-board) connector, a Molex 5050040812, that gives access to:

- MCU VDD, VUSB and GND

- MCU SWCLK, SWDIO and RESET

- Debug UART RX/TX

![../../_images/b2b-pinout.webp](https://developer.repebble.com/pebbleos/docs/images/b2b-pinout.webp)
_Pebble 2 Duo B2B connector pinout_

Plug the Core B2B v2 into the B2B connector as shown below, then connect it to the host over USB:

![../../_images/core-b2b-v2-connection.webp](https://developer.repebble.com/pebbleos/docs/images/core-b2b-v2-connection.webp)
_Core B2B v2 connected to a Pebble 2 Duo mainboard_

Warning

Connect the programmer in **exactly** this orientation. Any other orientation renders the watch unusable.

Press the connector until it clicks: when it is not fully seated, the serial console shows output but does not accept input. The programmer’s page explains its switches and firmware updates.

Once connected, the [pbl commands](https://developer.repebble.com/pebbleos/docs/pbl.md) flash, debug and reach the console of the watch.

Generated from PebbleOS [5285d4236](https://github.com/coredevices/pebbleos/commit/5285d423600370a73ae94b619748a69933107797). This page is maintained in the pebbleos repository: [docs/boards/asterix/index.md](https://github.com/coredevices/pebbleos/blob/5285d423600370a73ae94b619748a69933107797/docs/boards/asterix/index.md).
